Search found 45 matches
- 06 January 2020, 02:22
- Forum: Editor - Steps
- Topic: Active and unactive channels between steps [done]
- Replies: 17
- Views: 1735052
Re: Active and unactive channels between steps [done]
Thank you support for this change it is very useful. Sorry I didn't see it posted earlier.
- 18 July 2019, 00:34
- Forum: D512
- Topic: ShowXPress 512 DMX Signal to
- Replies: 4
- Views: 14627
Re: ShowXPress 512 DMX Signal to
I've seen something very similar where certain DMX devices would not work. On some equipment the D+ pin and the D- pin are reversed. Try making a cable as a test for the fixtures that do not work and roll those two pins. Leave the ground pin where it currently is connected. Typical wiring has Ground...
- 04 April 2019, 01:10
- Forum: Other
- Topic: Channels misaligned....
- Replies: 6
- Views: 12308
Re: Channels misaligned....
Data 1+ and - are often swapped over. The most commonly encountered pinout is given first.
Pin 1 Ground
Pin 2 Data 1- or 1+ (Primary Data Link)
Pin 3 Data 1+ or 1- (Primary Data Link)
Pin 1 Ground
Pin 2 Data 1- or 1+ (Primary Data Link)
Pin 3 Data 1+ or 1- (Primary Data Link)
- 16 February 2019, 02:30
- Forum: D512
- Topic: USB connection with D512 [fixed]
- Replies: 9
- Views: 20849
Re: USB connection with D512
Go to D512 hardware section and read about downloading and installing drivers.
- 26 January 2019, 03:44
- Forum: Editor - Generator
- Topic: Generator does not propose all the pan/tilt palettes
- Replies: 1
- Views: 5790
Generator does not propose all the pan/tilt palettes
I've created four palettes. Right, Left, Up, Down. When creating a step scene for a mover if I select Pan axis I see Right, Left Palette available as a position option. If I select Tilt axis I see Up, Down available as an option. But, In Generator with Pan/Tilt selected I only see Left, Right palett...
- 28 November 2015, 01:12
- Forum: General software
- Topic: Download link requirement for V8 alpha
- Replies: 91
- Views: 125107
Re: Download link requirement
Please send a link to the newest V8 for testing. Thanks Lightworx
- 21 May 2015, 00:04
- Forum: Live - Buttons
- Topic: Your suggestions for "sequencial cues"
- Replies: 51
- Views: 81209
Re: Your suggestions for "sequencial cues"
Thank You support !!!
- 16 May 2015, 02:18
- Forum: Live - Buttons
- Topic: Your suggestions for "sequencial cues"
- Replies: 51
- Views: 81209
Re: Your suggestions for "sequencial cues"
Thank you support for looking at this request. You are correct that in most hardware controllers (especially in the lower price range) a simple button push step function is provided. I would find it very useful for the software to allow me to select a scene then trigger steps within that scene with ...
- 03 May 2015, 00:15
- Forum: Editor - Steps
- Topic: One of my 4 Intimidator is fading in when i light them all
- Replies: 1
- Views: 6519
Re: One of my 4 Intimidator is fading in when i light them a
In Edit Mode check the little symbol under the channel for the fader. If it looks like a step the fixture will snap on, if it looks like a rounded step the fixture will fade on.
- 30 April 2015, 23:53
- Forum: Other
- Topic: Chauvet SPOT 250 light goes of when mooving
- Replies: 2
- Views: 8531
Re: Chauvet SPOT 250 light goes of when mooving
Make sure channel 12 is set to zero when moving pan or tilt. A value above 7 will command the fixture to blackout during pan /tilt moves.